Directions:
Begin By Preparing the Surface
Always test a small area before use to ensure that FAMOWOOD Dura-Tuff is compatible.
Aluminum:
- On new surface: Clean surface with commercial solution of phosphoric acid and rinse thoroughly with clean
water. Use ALODINE™ 1201 Coating chemical, which produces a light gold to tan chemical conversion coating
on aluminum, that provides corrosion resistance and paint adhesion.
- On old surface: Remove all paint, grease or oil contaminants can clean surface as above.
|
Fiberglass:
- Sand with medium grade production sandpaper until surface has a matte finish with no trace
of gloss or sheen remaining.
- After sanding, wipe with a clean cloth saturated with paint thinner.
Wood:
- Remove all old paint and san surface with course-grade production sandpaper.
- Fill all abrasions, dents, cracks and holes with FAMOWOOD Wood Filler.
- Sand with medium-grade to remove any scratches from previous sanding
and blend in filled areas.
- Finish snading with fine-grain production sandpaper.
- Remove all dirt and dust with a clean cloth saturated with paint thinner.
|
Applying To Surface
Follow these step-by-step directions when using FAMOWOOD Dura-Tuff Clear Coat:
- Dura-Tuff clear coat is ready to use. No mixing or thinning required.
- Maintain minimum 30% humidity in work area.
- TEST SMALL AREA BEFORE FULL USE. Apply only on dry surfaces, as moisture will stop
the curring process.
- Remove all grease, wax, paint, paint remover and other contaminants.
- Sand surface smooth and wipe clean with tack rag.
- Brush or spray on in one direction following the Brushing or Spraying steps noted below.
- If applied over existing paints or varnishes, check for compatibility, wrinkling,
loss of adhesion, etc.
- Always pour amount required for project into separate container. To prevent lip from sticking
to container, wipe clean and apply thin layer of paste was to these surfaces.
- Under average (70°F) conditions, Dura-Tuff Clear Coat dries tack-free in 2 to 4 hours. If more
than 8 hours has elapsed between coats, sand the previous coat.
- Brushes or spray equipment may be cleaned with lacquer thinner.
- COVERAGE: Approximately 100 square feet per quart.
NOTE: Always apply in well-ventilated area. Do not thin Dura-Tuff. Wear gloves and appropriate skin protection.
|
|
For technical support, contact our Technical Service Department by mail, email,
or phone. Our office hours are 7:30 A.M. - 4:00 P.M. (Central) Monday through Friday. Please contact us for more information.
To request a Material Safety Data Sheet (MSDS) please send an email to msds@eclecticproducts.com.
|
| What can FAMOWOOD Dura-Tuff Clear Coat be used on? |
MARINE: Above-water areas of fiberglass and wood boats, hydroplanes,
driftboards, canoes, oars, paddles, floorboard, seats, decks, walkways, and ultra violet protection for
clear epoxy resin surfaces.
HOME: Hardwood floors, exposed aggregate walk and driveways, protect
all types of metal, and ultra violet protection for clear epoxy resin surfaces.
SPORTS: Snow and water skis, fishing lures and poles, golf clubs,
bows & arrows, gym floors. Any sporting good where wear and tear on the coating is important.
INDUSTRIAL: Industrial floors, clear protection for all types of copper,
bronze, ferrous metals and aluminum. (Aluminum should be treated with ALODINE™ prior to
applying Dura-Tuff.) |
| Is FAMOWOOD Dura-Tuff Clear Coat easy to use? |
| Yes. FAMOWOOD Dura-Tuff Clear Coat is one of the easiest coatings
to apply and provides many years of protection. |
| How long does FAMOWOOD Dura-Tuff Clear Coat take to dry? |
| FAMOWOOD Dura-Tuff Clear Coat under average (70°F) conditions, dries tack-free
in 2 to 4 hours. If more than 8 hours has lapsed between coats, sand the previous coat.
FAMOWOOD® Dura-Tuff Clear Coat dries in 1/2 the time as varnishes. |
| What makes FAMOWOOD Dura-Tuff Clear Coat unique? |
- FAMOWOOD Dura-Tuff is a quick drying primer and an intermediate
and finish coat all in one.
- With FAMOWOOD Dura-Tuff, there is nothing to add or mix. This clear gloss,
moisture cure urethane replaces varnish and is non-yellowing and maintains superior adhesion.
- FAMOWOOD Dura-Tuff is UV resistant.
- FAMOWOOD Dura-Tuff is ideal for surfaces needing abrasion resistance.
|
| Can FAMOWOOD Dura-Tuff Clear Coat be used to protect steps? |
| FAMOWOOD Dura-Tuff Clear Coat is slippery when wet. For walking
or stepping surfaces, non-skid granules must be added. |
