E6000 Adhesives FAQs and Directions

Questions About E-6000, E-6100 and UV-6800 Formulas
	What are the directions for use and application notes?
	What applications can this be used for?
	What are the product specifications?

Directions:

Please read all directions before using. Use in a well-ventilated area only. Surface should be clean, dry and free from dirt. Roughen surface before use. Best when used between 70°F (21°C) and 85°F (29°C). Test small area before full use.
Apply E-6000 directly to the area to be repaired. For maximum strength, allow bond to dry for 24-72 hours. Cure time increases with lower temperatures and decreases with higher temperatures. Speed drying time by using a hand-held hair dryer. Set on low and do not hold directly on E-6000.
Clean uncured adhesive with acetone or naphtha. Cured material may be removed by cutting and scraping.
If E-6000 is used to adhere articles to fabric, DO NOT DRY CLEAN FABRIC.
E-6000 is not recommended for use on Styrofoam^™, polystyrene, polyethylene or polypropylene plastics.

For technical support contact our Technical Service department by mail, email, or phone. Our office hours are 7:30 a.m. - 4:00 p.m. (Central) Monday through Friday. Please contact us for more information.

To request a Material Safety Data Sheet (MSDS) please send an email to msds@eclecticproducts.com

Applications/Specifications:

COMMERCIAL APPLICATIONS

Seal leaks in PVC, ABS, copper and galvanized piping
Caulk or seal pools and spas
Bond metal to plastic appliance housings

FLEET MAINTENANCE

Seal windshields against moisture
Repair cracked or broken taillight lenses
Coat battery terminals against corrosion

PLANT MAINTENANCE

Seal cracks in concrete and cinder block walls
Seal & repair conveyor belts
Coat & protect boots & gloves

MARINE MAINTENANCE

Repair torn canvas sails & boat covers
Seal portholes against moisture
Seal wooden deck seams

E-6000

UNCURED MATERIAL

CURED MATERIAL

Solids: 30% by weight
Density: 11.1 lbs./gal.
VOC: 1.198 grams/liter
Tack time: 5 minutes
Full cure time: thin film: 24 hours; thick film:
48-72 hours
Storage: store between 50°F (10°C) and
80°F (27°C)
Freeze/thaw stability: yes; allow product to reach
room temperature before opening
Color: clear, white, gray, black
Viscosity: 50,000 cps (low), 100,000 cps (medium), 200,000 cps (high)
Shelf life: 2 years, unopened 50,000 cps (low),
100,000 cps (medium), 200,000 cps (high)
Shelf life: 1 year, unopened

Hardness: 80A
Tensile strength: 3,500 lb/in2
(ASTM D-412)
Elongation: 900% (ASTM D-412)
Chemical resistance: excellent to water,
dilute acids & bases
Temperature range: -40°F (-40°C) to 150°F (66°C)
Paint-over time: 24 hours
UV resistance: paint over or use
UV-6800™
Dielectric strength: 400 V/mil
(ASTM D-149)

E-6100

UNCURED MATERIAL

CURED MATERIAL

Solids: 32% by weight
Density: 11.0 lbs./gal.
VOC: 1.198 grams/liter
Tack time: 4 minutes
Full cure time: thin film: 24 hours; thick film:
48-72 hours
Storage: store between 50°F (10°C) and
80°F (27°C)
Freeze/thaw stability: yes; allow product to reach
room temperature before opening
Color: clear, white, gray, black
Viscosity: non-sag
Shelf life: 2 years, unopened

Hardness: 80A
Tensile strength:3,800 lb/in2 (ASTM D-412)
Elongation: 900% (ASTM D-412)
Chemical resistance: excellent to water,
dilute acids & bases
Temperature range: -40°F (-40°C) to 150°F
(66°C)
Paint-over time: 24 hours
UV resistance: paint over or use UV-6800
Dielectric strength: 400 V/mil (ASTM D-149)

UV-6800

UNCURED MATERIAL	CURED MATERIAL
Solids: 30% by weight Density: 11.1 lbs./gal. VOC: 1.198 grams/liter Tack time: 5 minutes Full cure time: thin film: 24 hours; thick film: 48-72 hours Storage: store between 50°F (10°C) and 80°F (27°C) Freeze/thaw stability: yes; allow product to reach room temperature before opening Color: clear Viscosity: 100,000 cps Shelf life: 2 yeasr, unopened	Hardness: 80A Tensile strength:3,500 lb/in2 (ASTM D-412) Elongation: 900% (ASTM D-412) Chemical resistance: excellent to water, dilute acids & bases Temperature range: -40°F (-40°C) to 150°F (66°C) Paint-over time: 24 hours UV resistance: to maximize UV resistance, paint over or use UV-6800^™ Dielectric strength: 400 V/mil (ASTM D-149)